Skip to main content

5V 8-Channel Relay Module

The eight-channel relay module contains eight 5V relays and the associated switching and isolating components, which makes interfacing with a microcontroller or sensor easy with minimum components and connections. Each relay on the board has the same circuit, and the input ground is common to all eight channels.

 

Eight-Channel Relay Module Pinout

Pin Number

Pin Name

Description

1

GND

Ground reference for the module

2

IN1

Input to activate relay 1

3

IN2

Input to activate relay 2

4

IN3

Input to activate relay 3

5

IN4

Input to activate relay 4

6

IN5

Input to activate relay 5

7

IN6

Input to activate relay 6

8

IN7

Input to activate relay 7

9

IN8

Input to activate relay 8

10

VCC

Power supply for the relay module

11

GND

Ground reference for the module

12

VCC

Power supply selection jumper

13

RY-VCC

Alternate power pin for the relay module

 

Components Present on an Eight-Channel Relay Module

The following are the major components present on the eight-channel relay module, which will be described in detail later in the article.

5V relay, terminal blocks, male headers, transistors, optocouplers, diodes, and LEDs.

 

Eight-Channel Relay Module Specifications

  • Supply voltage – 3.75V to 6V
  • Trigger current – 5mA
  • Current when relay is active - ~70mA (single), ~600mA (all eight)
  • Relay maximum contact voltage – 250VAC, 30VDC
  • Relay maximum current – 10A

 

Alternate Relay Modules

Single-channel relay module, dual-channel relay module, four-channel relay module.

 

Alternate Modules

SCRs, TRIACs, Solid State Relay module.

 

Understanding 5V Eight-Channel Relay Module

Eight-Channel Relay Module

The eight-channel relay module contains eight 5V relays and the associated switching and isolating components, which makes interfacing with a microcontroller or sensor easy with minimum components and connections. There are eight terminal blocks with six terminals each, and each block is shared by two relays. The terminals are screw type, which makes connections to mains wiring easy and changeable.

 

The eight relays on the module are rated for 5V, which means the relay is activated when there is approximately 5V across the coil. The contacts on each relay are specified for 250VAC and 30VDC and 10A in each case, as marked on the body of the relays. The switching transistors act as a buffer between the relay coils that require high currents, and the inputs which don’t draw much current. They amplify the input signal so that they can drive the coils to activate the relays.

 

The freewheeling diodes prevent voltage spikes across the transistors when the relay is turned off since the coils are an inductive load. The indicator LEDs glow when the coil of the respective relay is energized, indicating that the relay is active.

 

The optocouplers form an additional layer of isolation between the load being switched and the inputs. The isolation is optional and can be selected using the VCC selector jumper. The input jumper contains the main V­CC, GND, and input pins for easy connection using female jumper wires.

 

Internal Circuit Diagram for Eight-Channel Relay Module

The circuit on the board is as follows:

Eight-Channel Relay Module Circuit Diagram

Each relay on the board has the same circuit, and the input ground is common to all eight channels.

 

The driver circuit for this relay module is slightly different compared to traditional relay driving circuits since there is an optional additional layer of isolation. When the jumper is shorted, the relay and the input share the same VCC, and when it is open, a separated power supply must be provided to the JD-VCC jumper to power the relay coil and optocoupler output.

 

The inputs for this module are active low, meaning that the relay is activated when the signal on the input header is low. This is because the indicator LED and the input of the optocoupler is connected in series to the VCC pin on one end, so the other end must be connected to the ground to enable the current flow. The optocoupler used here is the PCF817, which is a common optocoupler that can also be found in through-hole packaging.

 

How to Use the Eight-Channel Relay Module

The eight-channel can be used to switch multiple loads at the same time since there are eight relays on the same module. This is useful in creating a central hub from where multiple remote loads can be powered, which is useful for tasks like home automation where the module can be placed in the main switchboard and can be connected to loads in other parts of the house and can be controlled from a central location using a microcontroller.

Eight-Channel Relay Module Application Diagram

In this diagram, eight separate loads (represented by lightbulbs) have been connected to the NO terminals of the relay. The live wire has been connected to the common terminal of each relay. When the relays are activated, the load is connected to the live wire and is powered. This setup can be reversed by connecting the load to the NC terminal, which will keep it powered on till the relay is activated.

 

Eight-Channel Relay Module Basic Troubleshooting

If either of the relays does not turn on:

  1. The contacts might be welded due to overcurrent/arcing. Shaking the module firmly might help unstick the contacts.
  2. The driver circuitry might have been damaged due to overvoltage.
  3. Input polarity might be incorrect.
  4. Jumper might not have been moved to the correct position

 

Eight-Channel Relay Module Applications

  • Switching mains loads
  • Home automation
  • Battery backup
  • High current load switching
Component Datasheet

Related Post



Join 20K+subscribers

We will never spam you.

* indicates required

Be a part of our ever growing community.